Home › Blog

TUPY Pipe Fittings Blog

News, products, standards, installation guides and events from TUPY and its Middle East agent.

Steel Pipe Galvanised Pipe Industrial Pipe Stainless Steel Pipe Fluid Transfer Pipe Fire Protection Networks Gas Piping Building Services Steam and Industrial Hot Water Industrial and Petrochemical Selection and Buying Guide Standards and Certifications
What to Ask a Fittings Supplier For, and How to Read It Standards and Certifications

What to Ask a Fittings Supplier For, and How to Read It

A rejected submittal is almost never about price. It is about paperwork nobody asked for when the order was placed. The documents worth requesting, what each one proves, and the four questions that separate a certificate that survives scrutiny from one that does not.

8 September 2026
Read more
DN, NB or Inches: Sizing Pipe Fittings Without the Ordering Mistakes Selection and Buying Guide

DN, NB or Inches: Sizing Pipe Fittings Without the Ordering Mistakes

A drawing says DN 25, the BOQ says 1 inch, and a caliper reads 33 mm. Only one of those is a measurement. How nominal sizing works, how to get from a caliper reading back to a size, and how to write a reducing fitting so it arrives the right way round.

8 September 2026
Read more
UL Listed and FM Approved Fittings for Sprinkler Work Under NFPA 13 Fire Protection Networks

UL Listed and FM Approved Fittings for Sprinkler Work Under NFPA 13

Gulf fire protection is usually written to NFPA, and a sprinkler submittal gets read line by line. What NFPA 13 asks of a fitting, why UL Listed and FM Approved are two separate things, and why an approval attaches to a figure and a size rather than to a brand.

8 September 2026
Read more
Salt Air, Humidity and 50 °C: How Galvanised Malleable Iron Behaves in the Gulf Galvanised Pipe

Salt Air, Humidity and 50 °C: How Galvanised Malleable Iron Behaves in the Gulf

Chloride in the air, condensation on cold surfaces and a long daily time of wetness make the Gulf hard on metal. How a hot-dip coating protects, where it actually gives way - almost always at something created on site - and what to do about it at the joint.

8 September 2026
Read more
GI and MI Pipe Fittings in the UAE: Sizes, Standards and What to Check on Delivery Galvanised Pipe

GI and MI Pipe Fittings in the UAE: Sizes, Standards and What to Check on Delivery

GI and MI describe the same fitting from two angles - the coating and the metal. A working guide for the Gulf: the grade and the standards behind it, how the range is sized, BSP against NPT, and the ten-minute check worth doing before a pallet is broken down on site.

8 September 2026
Read more
What Is Malleable Cast Iron and Why Are Pipe Fittings Made from It? Selection and Buying Guide

What Is Malleable Cast Iron and Why Are Pipe Fittings Made from It?

Malleable cast iron is not the same thing as ordinary cast iron. A long heat treatment turns a brittle material into one that deforms under impact instead of breaking — and that difference is what made it the standard material for pipe fittings.

16 August 2026
Read more
The Difference Between BSP and NPT Threads in Pipe Fittings: A Guide to Telling Them Apart Selection and Buying Guide

The Difference Between BSP and NPT Threads in Pipe Fittings: A Guide to Telling Them Apart

BSP and NPT threads look very similar but are not compatible. This article explains the difference in flank angle, crest form and reference standards with a diagram, and shows how to tell them apart on site.

16 August 2026
Read more
What Are Brazilian Fittings? A Complete Introduction to TUPY Fittings Selection and Buying Guide

What Are Brazilian Fittings? A Complete Introduction to TUPY Fittings

In the regional trade, “Brazilian fittings” effectively refers to one brand: TUPY. But why did the fittings of a Brazilian foundry become the market benchmark, and how do you tell a genuine fitting from a counterfeit?

16 August 2026
Read more
A Guide to Choosing Pipe Fittings: Malleable Cast Iron, Galvanised or Black? Selection and Buying Guide

A Guide to Choosing Pipe Fittings: Malleable Cast Iron, Galvanised or Black?

Choosing pipe fittings is not just choosing a size. The material, the coating and the accuracy of the thread decide whether your piping system runs for ten years without a leak or causes trouble in its first year.

16 August 2026
Read more
Why the Choice of Fitting Material Determines the Life of a Piping System Selection and Buying Guide

Why the Choice of Fitting Material Determines the Life of a Piping System

Fittings are the point at which piping systems actually run into trouble. This article looks at why malleable cast iron behaves differently from brittle materials under impact, vibration and pressure, what part thread accuracy plays in preventing leaks, and what to check when buying a fitting.

8 August 2026
Read more
1